To maintain the lubricative properties of oil, the oil cooler by cooling the oil (having it flow through it galleries) to the proper temperature range. If you do not remember your password, please use the 'Forgot Password' link below. Before removing the upper intake bolts off, you have to remove the heat shielding pad from behind the engine. 3.6L Oil Filter/Cooler Adaptor Housing Replacement. Advance Auto Parts has 1 different Engine Oil Filter Housing for your vehicle, ready for shipping or in-store pick up.
Remove (2) 10mm heater line mounting nuts. 3" and 6" extensions. A slow leak may not be obvious right after install but hopefully it will leak never again!!! Hear from other customers via the 98 reviews on parts for your Jeep Wrangler. Log Into My Account. Located closer to the firewall, there is a wire loom held on by keepers that need to be pried/removed. Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM. Be careful with the injectors. Jeep Wrangler Oil Cooler Repair Costs. The dealership is around $240. How will you know if your oil cooler is leaking? Clean out all old oil from the oil filter/cooler housing mounting valley. Remove 10mm nuts on the bracket located on the right side of the intake neck, behind the throttle body. It goes at least an inch into the top of engine valley so it may be a little tough. This time it is allowing oil into the coolant.
Don't forget the two 10mm bolts that hold the intake pipe onto the top of the radiator fan shroud. Parts Recommended: Upper and Lower Intake Gaskets – MS97204. Once the brackets are removed you can remove the pad and reach the back upper intake bolt easier. INTAKE REMOVALE: First start by removing the two EGR/intake tubes located on the left side (passenger side) of the intake neck. You should now be able to remove all eight 8mm lower intake bolts and carefully remove remove the intake. Tools Required: - 8mm Socket. Jeep 3.6 oil cooler upgrade your flash. Suggest cleaning the gasket surfaces before reassembly and cover the intake ports until reassembly as to not get anything inside the engine. The engine oil cooler filter housing adapter kit keeps the engine oil clean and cool as it circulates through the engine. After removing the upper intake, its time to unplug all the fuel injectors and remove the fuel line. Remove foam from behind the upper intake at firewall. Using a body tool remove (3) wiring clips used to secure the Map Sensor wiring. You will not be able to get the rear coolant hose or clamp off the adaptor housing while it is still mounted in the valley. If you do not have an account but would like to check the status of an order, request a change, or report a problem with an order or shipment, please go to our. Oil filter/cooler mounting bolts are torqued to 106 in lbs in a pattern starting from driver side rear, the driver side front, passenger side rear, passenger side front and the very front being torqued last.
Remove all 7 upper intake bolts as listed in the provided All-DATA pages. Oil Filter/Cooler Housing – 68105583AE. Please set a password for your account. You should be able to wiggle and lift the housing up and out. Small flat tip screwdriver.
6L V6 Chrysler 200, Town & Country, Dodge Grand Caravan, Jeep Grand Cherokee, Wrangler, Ram 1500, 2500. This will help keep unwanted debris out of the intake port after pulling the lower intake off. Oil adaptor housing part #5184294-AE (2011-2013) and part #68105583-AE (2014-2016{refer to other posts in this thread in regard to the difference}) You can find the part online much cheaper than the dealership (buy at your own risk). Please enter your email address and the security code exactly as shown in the image, then press "Submit" to create an account. I will post as many photos as I can that will aid you, if you choose to tackle the project yourself. NOTE: The injectors and/or the O-Rings may stay in the manifold or fuel rail when removing the fuel rails. Genuine Jeep Wrangler Oil Cooler Engine Oil Cooler. Mexican Pesos (Mex$). Atomic: I have an appointment with the dealer to get it fixed, and it's a 100 dollar deductible so it's not a big deal but... Fits the following vehicles: Replaces part numbers: 68105583AF, 68105583AE, 68105583AA, 68105583AB, 68105583AC, 68105583AD. Jeep 3.6 oil cooler upgrade for jeep grand cherokee 2014 limited 4x4. Both sides are held on by a pipe clamp and can either be taken off with a flat head screw driver or an 8mm socket. 12-month / 12k-mile warranty. Some manipulation of the housing is required to get it back into the mounts.
Remove the (2) Vent lines on from of the upper intake. Confirm New Password. Ordered a new Oil cooler assembly using the Dorman aluminum housing that will update the filter to the late style 14 & up. I just had yet another oil cooler/filter housing break on my 2014 Rubicon. Log In or Create Account (Optional). Jeep Wrangler Engine Oil Filter Housing | Advance Auto Parts. Engine Oil Cooler and Filter Housing Adapter Kit - Replaces 68105583AF, 68105583AE - Fits 3. Real customer reviews from Jeep owners like you. Remove sensor plug and throttle body plug. Yep, cost reduction and in some cases lighter weight. Most recently I purchased a wiper transmission for my Wrangler - a discontinued Mopar part.
From underneath, you will not be able to see the exact point of origin the oil is emitting from. The oil filter housing can easily be located above the engine and can be accessed by removing the intake manifold. You will also need a pair of pliers and a screw driver for the removal of some clamps and hoses. Wiring connector bracket bolts 89 in lbs. I did not buy OEM intake gaskets. Once the bolt studs are past the bracket and you can lift up, you should be able to pull the upper intake up and out towards the driver side. Remove 2 plastic body clips (on back of the upper intake). Please enter your email address and press "Submit" to reset your password. Remove (2) 10mm bolts holding wiring connector on passenger side. Remove (2) clips on rear of the upper intake on the passenger side. Connect the Oil Temperature and Oil Pressure wiring to the Oil Filter/Cooler Housing. Fits Wrangler (2012 - 2013). Carefully pull the blue safety clip from the fuel line and you should be able to squeeze the white clip. ALL THE PARTS YOUR CAR WILL EVER NEED.
To keep the engine oil as clean as possible, it is best to change the oil at 3, 000 to 3, 500 miles. Remove electrical connector on the bottom of the throttle body opening. Before you unbolt or remove the lower intake, it is important to pry/remove the back wire looms that are secured to the back of the intake. I will post the All-Data pages I have to also give you an idea of the only intake bolts that should be removed. Order Status & Returns. Primarily used in air-cooled and motorcycle engines, an oil cooler serves two purposes, lubrication and cooling.