The belt placement tool allowed us to remove and properly place the new belt without reaching down into the pulley area. That is the big long belt in the front of your engine. And as mentioned above, a bad tensioner could lead to other engine damage. Fits: Mazda CX-5 2014-2023 (non Turbo). Reattach the mounting bolt. 12 mm flare nut wrench: Used to install the belt tensioner bolt.
AFA your question, just keep monitoring the tensioner, and it's likely to be ok as long as it remains only a light weep. Mazda recommends that the serpentine belt is replaced every 35, 000 miles. When Should You Replace The Drive Belt Tensioner? 4 FAQs On Drive Belt Tensioner Replacement. 17 mm crow foot flare nut wrench: Used primarily to remove the water pump belt via the "Cast Hexagon". One of the keys to maintaining an operational engine and full use of your accessories is keeping an eye on your Mazda CX-5 drive belt tensioner.
Fuel Injector - Service. To remove the serpentine belt on a Mazda, you must remove the passenger side wheel. A drive belt tensioner is designed to last the entire lifespan of a vehicle. Note: A vehicle may have a manual or automatic belt tensioner (spring-loaded idler pulley). Start thinking about changing the timing belt once you cross the 90, 000-mile threshold. STEP 2: removing & installing the belt tensioner. The video above shows how to check the serpentine belt on your 2013 Mazda CX-5 - if it gives more than a half inch when pressed, is cracked, frayed or appears shiny, you should change it (or have it changed) immediately. Close up of serpentine belt tensioner. Remove the belt with a serpentine belt tool.
Does the timing belt on my MAZDA make noise? However, you could need a replacement as early as 50, 000 miles due to unexpected wear and tear. Ensure that there's proper belt tension. Because if you let the noise go on for too long and your timing belt breaks, the result is an expensive headache you don't need. Engine Oil Flexible Maintenance is selected by default for U. S. A. and Puerto Rico residents. Product Code: PY01-15-909A-2776. Both are a sign that your drive belt tensioner needs a replacement. Refer to Maintenance Monitor (Search) for the details. 10mm socket to remove the access panel. Driving for long periods in cold temperatures or extremely humid climates. This yields the maximum visibility and also the maximum leverage. 12 mm ratcheting wrench. You will need to use a cheater bar to move the tensioner back.
Verify that the indicator part of the cast hexagon on the drive belt auto tensioner is within the normal range.. 7. Shop online, find the best price on the right product, and have it shipped right to your door. The belt is attached to both the crankshaft and these systems, and transfers power from the engine to drive each of these components. If you prefer to shop in person for the right Belt Tensioner Assembly products for your CX-5, visit one of our local Advance Auto Parts locations and you'll be back on the road in no time! Pull the cloth in the direction of the arrow and rotate the crankshaft pulley clockwise. If so, then most likely your belt tensioner has gone bad and the belt is now slipping making that sound or the bearing on the tension pulley has gone bad. Reinstall the engine mount parts.
Now, instead of separate belts for each component, most cars today use a single wider, multigrooved "serpentine" belt (aka as serp belt), named for the way it snakes around multiple pulleys. 1x Genuine Mazda - Drive Belt Tensioner. Measure wear with an app. Using my primary ratchet + flare nut crow foot to remove the serpentine belt. Afterwards, you will need to apply tension to the "Cast Hexagon" counterclockwise, then push the belt onto the (3) Crankshaft Pulley and (4) A/C Compressor Pulley. Project step-by-step (11). Our mobile mechanics offer services 7 days a week. Some of these steps may be difficult to do at home without the right tools. Within a few minutes, your Mazda engine will shut off as it runs out of battery power. Although a TSB does not imply providing extended coverage outside of warranty, Mazda will sometimes offer partial or even full compensation for well know problems, particularly if you've had maintenance done by them. Apply a clean cloth to the water pump drive belt as shown in the figure. ITEM 5 - CX-5 Water pump belt.
The first test is a visual inspection with the engine running to assess the dampening feature of the tensioner. Mazda CX-5 Serpentine belt | Mazda OEM Part Number PY01-15-909A. Eye Protection: I got shot in the eye with flying splash shield rivets/sand when trying to pry it off because a few of them had sand stuck inside or they just wouldn't come out. Spark Plugs - Replace. If ignored, tensioner housing cracks could result in belt failure or destroy parts in front of it, like the radiator. Install the new tensioner onto the engine using the torque wrench to fasten the tensioner bolt (pulley bolt). Belts themselves aren't that expensive.
What happens if your Mazda serpentine belt breaks? Timing Belt - Replace. Install the generator drive belt. Inner wheel splash shield (held on by 4 rivets). Given all the hassles associated with performing maintenance on your car or truck, let be the most authoritative website you go to make purchasing it easy.
Luckily, I was wearing eye protection so I would HIGHLY RECOMMEND doing so. Newer models use timing belts made of polyurethane and Kevlar for long life and durability. Tip: Do check your manufacturer's warranty to see if it covers replacement costs.