If there is another pin that goes through the cap, be sure to put that back where it belongs. There are two resistors, a diode, three wire jumpers, a linear position sensor, and 5 tactile switches. Traxxis Control Board Diagnostic and Replacement | Minn Kota. For Use With: -Minn Kota Endura Max hand control models. Next, we used a multimeter to check the total resistance of the positional sensor. So, if your trolling motor prop is not spinning at all, this is a chance that you have been operating your trolling motor with dirty brushes, and the armature has completely burnt out. Where: Both the brushes and the armature are located in the lower-unit housing of your trolling motor. Minn Kota Terrova 112 Thrust 36V Main Control Board #2774014. The link to the video of the original controller can be found here: He wanted us to publish this build on the TechForum because of the great response he got from his YouTube channel - where several viewers asked how to build it. We are a authorized repair center as well as a dealer. Spray lubricant onto each end of the shaft where it connects to the propeller. First issue ive had.
If you are not comfortable with this, contact Minn Kota for the location of a certified service agent in your area. 00 Availability:: Usually Ships in 1 to 2 Business Days Product Code: 2774016 Qty: Description 12 Volt Terrova and Riptide ST Bow Mount The 12 volt control board assembly offered here is made to fit the 12 volt Terrova bow mount, or the 12 volt Riptide ST bow mount motors. Minn kota control board repair. The most common reason is that the motor is overloading and drawing too much current. The amp draw under bench test, no load, conditions should be less than 2 amps for a 12-volt drive housing, and less than 1.
Anyone else have this happen? Lakeside Marine & Service is a Minn Kota Authorized Service Center. Minn Kota Armature Replacement. Be sure always to clean your prop after every use and remove any weeds or fishing line you may find. The first 3 times I had it out it worked great, easy to learn and maneuver around today it was working fine to start then we moved to another spot and then no steering left or right, however everything else worked fine.. Where: The control switch is located in the top of the trolling motor where the hand controller comes out. The 4 switches on the bottom left and bottom right are used to change direction of the motor, and we realized that a DPDT switch could accomplish the same thing. Question - Minn Kota Riptide ST w/I-pilot troubleshooting. Once inside, remove the hand control and remove all the wires from the control switch. If the higher than normal amp draw of the drive housing is not corrected the steering circuit on the new/replacement control board will also fail.
With these two new connections connect them to pins 3 and 4. The top resistor is used for limiting current to the positional sensor. Minn Kota motherboard problem - General Forum. To make the foot pedal and interchangeable with the control box, part number SC277-ND. Let's get down to the solutions. Over the years I have fried 2 24 volt motherboards and believe a fishing buddy may have fried his post 17 board. Does anyone know of a way to test the pedal with a multimeter?
Smooth fast and accurate purchase. This may be covered warranty as well, so be sure to ask. Spray lubricant into both ends of the motor and distribute the lubricant evenly. Part Number: 2074070. I then took a picture of the bottom of the board and traced out the leads with their corresponding wire color to better understand their connections. How to test minn kota control board game. Once your boat is in the water, take the trolling motor and mount it onto the transom. In addition, you have to press either its forward or reverse control switch five times within five seconds. Inside this compartment are the control switch, the hand control, and the wires from the battery to the armature. 250" quick connect to this splice on the wire. You give the motor some power but no movement. After buying a new pedal, the momentary and continuous works, but steering does not.
There are markings on the control switch to show you which wires go where. Power into but no power out at any setting. We have an article covering serial numbers in detail and where to locate them on most motors. Don't forget to share it with your other fisher friends if you like our work. Many different things can cause this, but first, you need to determine if the motor is drawing too much current or not. It worked last time I hooked it up to a battery, but now it just does nothing. How to test minn kota control board.com. To make the potentiometer more waterproof, we chose a rotary shaft seal to make the potentiometer as IP rated as possible. Step 2: Unscrew the nut under the shaft with a wrench. We decided to do this because this cable has the most connections. When this is done, we will only "capture" the necessary shipping and handling amount and/or issue your account a partial refund for the shipping overcharge. Control board seems to work just fine: Works great thank you. A broken prop drive pin is most often the result of your prop coming into contact with something hard like a rock, submerged log, or the seafloor.
If not, it's time to troubleshoot or take it to a professional for repairs. Afterward, you are going to want to address this issue immediately. Part came quick and installing was an ease. In case you don't have a 12-volt battery, you can test it with the help of another boat. Shows That the unit is getting power ( battery test button and autopilot light work)Tried to fish some docks today but got a little dangerous so we quit early today. Came sooner than expected. You do not want future leaks. The diode is used as a flyback diode for the relay that is on the main control board of the trolling motor.