That appears to have done the trick Todd. I've once tried to use Tru oil finish on my rosewood back without pore filling (only seal it with shellac) and the result was horrible. Would would the Johnson's paste wax cause a problem down the road if the neck needed refinishing? I put it on Ed Caffery style so its extremely thin layers but some times 24-48 hours later its still tacky. Is this a feature of tru oil finishes or did I do something wrong? Thought I would revive this one to ask if consensus is to tape off the ferrule, as Bmoze does above? If you have to work twice as hard and take an extra half a day to smooth out the finish you just applied, then you are wasting valuable time. How to coat gun stock with Tru-oil finish? One thing to try is to clean the handles thoroughly with acetone to remove any oils/waxes that may be ' wrote: ↑ Tue Nov 27, 2018 2:17 am Thanks for the info all. But enough of them do that it is good practice to sand between coats all the same.
Designed for finishing gun stocks, this is a very durable finish that will last under fairly hard use. I usually rub ( wisker) my walnut gun stocks with cloth from an old pair of levis between coats after each your bottles upside down. Tru Oil is a concoction that leaves behind a varnish after some of its contents evaporate. The bulk of the preparation involves sanding to get rid of any flaws and smooth up the surface. Originally posted by hhunter44. Its not the wood species either because it does the same with walnut, maple or cocobolo. Alternatively, you could cut to the chase and just use a polyurethane product that already comes 'pre-thinned' in the form of Wipe-on Poly. When the stock has soaked up all it can absorb, wipe away the excess and let dry for 24 hours (Read Carmichel's Tip below). I will report back when it is playable again.
I don't let the wood get too hot but the warm constant air does speed up the cure time. I use it on any furniture I build because it requires no rubbing out when applied with a rag, and is very hard wearing. You do not need to wait a month. Unless I have an application problem, I have started applying 3-4 coats before steel wool to prevent going through to the stain. Joined: Sunday 09 May 2021, 02:02 am. So, keep reading to learn all of the key tips and tricks you need to know about applying that final poly coat to perfection. Tung Oil Needs Regular Re-Treating. You do not want dust getting on the still wet finish. When you apply Tru Oil finish on top of the Tung Oil layer, there is no need to sand down unless there is substantial surface damage or dirt. Tru oil makes wood glossier, which works for wood with a deep hue like walnut and oak. Frequently Asked Question. A lint-free soft cotton material is best; I like to use old worn-out tee shirts.
A wooden deck is an example of this because people can wait for a limited time before they need to step on it. What is Tru Oil and Tung Oil? My 1st guitar I finished with Tru Oil and the rosewood never dried. From Linseed oil to Teak oil, almost all oil finishes need some kind of protective top coat. 4 coats over 4 days probably produces a nicer overall finish than my 2 hour method but I expect temperature and humidity probably plays into this quite a bit too. I went as high as 12 coats and 24 hour cures between for some muzzle loaders I built.
Neither of these is universally better than the other, especially when Tru Oil actually contains Tung Oil. A seal coat of thinned shellac as Todd suggests is a great way to start the finishing process with varnish/oils because the shellac will stick to almost anything, and it will isolate the wood from the varnish. Tung Oil might not be the best option if someone is searching for a finish option that requires little upkeep. That said, it's always best to start with a fresh bottle. But that's not entirely true. Wooden coasters, photo frames, shelf-dividers, and book-ends are all examples of small projects that are crafted out of wood and are meant to look good. Keep it away from sources of intense heat and light. Can Tru Oil Be Applied Over Tung Oil? Tru Oil and Danish Oil both contain Tung Oil which acts as a strengthening agent with waterproofing qualities. Both Are Water-Resistant.
Your stock is now totally filled, protected and ready for the finishing coats. I have not been able to identify which species are worse than others, I've had pieces from the same larger block of wood act differently. TruOil is essentially a varnish that has been thinned with mineral spirits, and drying oil.