Turn off the power to the socket and remove the plug. Also try turning down the power output of the RBRs wifi radios from 100% to 25% on the 5Ghz radio and see if this changes anything. Also, ensure that your Wi-Fi password doesn't contain any special characters that could be interpreted differently. Move the router and the Sync Module. When connecting your Blink Sync module, ensure that you use a 2.
It should help you troubleshoot the issue and get it going again without having to do a complete factory reset or deleting all your cameras from your Sync Module. The reset button of the Blink outdoor camera can usually be found on the bottom of the device. Wait for its light to blink blue and remain green. A red light would mean that the module has lost its internet connection. Release the Reset button and wait 30 seconds for the router to fully reset and power back on. I was pretty sure it said green light ON and blue light blinking, but 'no matter'. To reset a Blink Mini: - Long press the reset button present on the button of the device, for about 5 seconds. Connect the Sync Module to your own Wi-Fi.
It is usually a small button, on the back or at the side of the device. Resetting restores the factory release firmware and helps clear out any corrupt config files that could prevent it from connecting to your network. Remember that you should first power cycle the system before resetting if problems arise. If you read my little story on the Sync Module article, you'll know I had IP conflict issues at one time but I easily fixed it. Hello my blink sync module is awsome well worth it and to the worker that help as well awsome serviceI would recommend this to a friend.
At the same time, pull up the battery cover. Click on "Delete" to confirm. Power cycle the Sync Module. You will need to look up your particular model to get the correct instructions for a factory reset. I would recommend this to a friend. The Blink Outdoor Camera needs a compatible Sync Module to work.
Continue reading to find out when you should reset and how you can power cycle or reboot your Sync Module. To ensure your Blink camera has a strong internet connection, you must place the sync module in an appropriate position and check for signal strength using the Blink app. If your camera runs on batteries, remove them and wait for a few seconds before putting them back. Ensure that MAC address filtering is off on your router.
This usually happens because your Wi-Fi is unstable or something like that—and this issue may be resolved in a few minutes without you doing anything. The blink sync module indicator light should guide you when troubleshooting a connection problem. Not only does it allow you to connect your camera to the internet, but you can also save the camera's battery life by using the device. Some blink older firmware can't decrypt such characters, leading to a connection failure. Although for the cameras that connect to the Sync Module, you would reset the module instead of resetting the camera itself. Your Blink Outdoor Camera does not come with a Wi-Fi chip; it's just a camera, after all.
Keep in mind that interference between the Sync Module and the camera can reduce the maximum distance. Release the button when the modem lights start to flicker. I ended up returning the new one because the original one did not break, the problem was with my router instead. By itself, your Blink Outdoor Camera is just a camera—and nothing more. Being too far from the module can prevent the camera from syncing. I have an Orbi RBR50 with two satellites set up in my home. Rated 4 out of 5 stars. Tips to Fix Blink Sync Module Offline Issues. Great camera systemPosted. If you experience functional problems with your sync module.
When you buy through links on my blog, I may earn an affiliate commission. The Sync Module helps your Blink Outdoor Camera perform at optimal capacity. Repeat steps 11 and 12 for all the cameras you own. Locate the power adapter of the Sync Module. I purchased this device separately from the cameras because I did not know this device was included in my Blink camera kit. If the two accounts are not already linked, then you will be prompted to link the device with Amazon. Whether you are using an Android device or iPhone, just close the Blink application from the recent apps and then try re-launching it. Connection issues can also be caused by slow internet, so make sure your internet is fast enough to handle the traffic from a Blink camera security system. Look for Restore or Factory Default. Wait at least 45 seconds before plugging the Sync Module back in. With help from Blink support, now working great. Let the module complete the setup process.
Check that Your Internet is Working. At least Blink has a way to display the password that was entered (and not persist in showing 'dots'). If so, toggle it on, and reboot your router; once the changes are applied, try reconnecting your sync module. After doing this, try reconnecting your Sync Module. If your blink module has no lights, then the power connection isn't working – either the power cord or outlet has tripped. So you can try all of these tips one by one when your Blink cameras lose internet connection and if none of these solutions work for you, contact Blink customer support on their website. When I checked out online on why this could happen, I found that it could be traced to a number of reasons. Blink cams work with 2 AA lithium batteries that can last up to two years of course depending on the usage, and when these batteries are close to death the camera will lose some of its power and can't attract reliable internet signals to operate efficiently.
When the Sync module is not the cause of the issue and it's working perfectly but your camera is still offline try to power cycle your modem and router. Your Blink Sync Module should reconnect and come back online after this. As mentioned earlier, you can get your Sync Module back online by rebooting your router and the device itself.
If the problem still persists, you can seek help from Blink's technical support. And for iOS users, go to your App Store and update your Blink App. Editors' Recommendations. Let go of the button when five seconds pass, and you'll see a light flash red.